Change or rekey · Langton
Lock Replacement & Upgrade in Langton
The lever on the side door droops toward the floor and rattles in your hand.
In plain words
After a break-in or an attempt, the door tells a story, and the new hardware should answer it. Splintered wood around the strike means the jamb gave before the lock did, so the repair pairs a heavier deadbolt with a reinforced strike and 75 millimetre screws that reach the framing behind the jamb. A bent bolt or cracked housing is replaced with a graded deadbolt whose bolt has a hardened core. A knob lock that was bumped or forced is swapped for a set with better pins. The aim is a whole opening that resists force, not merely a shinier lock.
How the visit goesThe brass handleset has gone blotchy and green where the winter salt reaches it, and the coating on the deadbolt is lifting in flakes. It still locks, but it looks tired beside the fresh paint on the door.
Lock Replacement & Upgrade
How the visit goes
How the old lock behaves in use
The locksmith works the existing hardware the way you do every day and watches for the tell-tale signs. A key that must be lifted or wiggled points to worn pins or a worn key. A knob that turns too far, or a lever that droops, suggests a tired spindle or spring. A latch that stays retracted, or a bolt that stops short, can be internal wear or something outside the lock altogether. Doing this with the door open first, then closed, separates faults inside the mechanism from faults in the fit of the door, and that distinction decides whether new hardware is the answer or part of the answer.
Taking the old hardware off without harm
Removal is done with the same care as fitting. Interior trim screws come out first, then the interior rose or thumb-turn, and the exterior housing lifts away with its tailpiece. The latch or bolt slides out of the edge bore once its two faceplate screws are released, and the old strike comes off the jamb. Painted-over screws are scored free rather than forced, seized screws are eased with a hand driver of the right size, and a stripped head is drilled out only as a last step. The bore and edge mortise are then cleaned of paint build-up and debris so the new parts seat properly.
A smart lock with its backup arranged
A keypad or smart deadbolt leaves the visit with codes set for each person, auto-lock and alerts configured, and any phone pairing confirmed while the locksmith is there to check it. You are shown the low-battery signal so you recognise it, and the type of battery the maker calls for. The mechanical override key is the piece to look after: keep it on a keyring or with a neighbour rather than inside the home it opens. A second person's code is set up before the locksmith leaves, so a flat phone or a forgotten code is never a reason to stand on the porch.
Lock Replacement & Upgrade
In the van
Graded deadbolt
Knob or lever entry set
Boring jig and hole saws
Adjustable latch or bolt
Cylinders, plug follower and pinning kit
Lock Replacement & Upgrade
What affects the quote
Special-order hardware
Most standard locks come from the van. A specific style, an unusual finish or a restricted system may need ordering, which affects scheduling and is noted in the quote rather than discovered on the day.
Smart lock setup
Fitting a keypad or smart deadbolt includes programming codes, pairing to a phone or hub and calibrating the bolt, which is time on top of the mechanical installation and is named in the quote.
Strike reinforcement and jamb repair
A reinforced strike with long screws is a modest addition; repairing a jamb split from a forced entry, or fitting a strike box into a frame that has never had one, adds labour and materials.
What to have ready
- Which doors are you thinking about, and what is on each one now?
- Is the problem wear, damage, looks, a change of function or too many keys?
- Are you interested in a keypad or smart lock on any door?
Lock Replacement & Upgrade: questions
QuestionsMy door has glass beside it. Should I fit a deadbolt keyed on both sides?
A keyed interior cylinder means finding a key to get out, which is not what you want on a door people use every day. The steadier answer for a door with glass is a single-cylinder deadbolt with a thumb-turn, combined with a reinforced strike, a longer bolt and a security film or laminated glass in the sidelight.
Can the same visit replace locks on more than one door, or does each door need its own appointment?
One visit usually covers every door on the job. The locksmith brings a range of cylinders and strikes, measures each door's backset and bore, and works through the list in order, front entrance first if a key change matters most there. Having a rough list ready, which doors, and whether they should end up on one key or several, lets the locksmith plan hardware before arriving rather than working it out door by door on site.
My old house has a mortise lock. Can it take modern hardware?
Often the original case can be kept and given a new cylinder and strike, which keeps the period look and the old door intact. Where the case is beyond service, a filler or conversion plate covers the mortise pocket and lets a cylindrical deadbolt or knob set be fitted without cutting into the door's stile. The locksmith looks at the door before recommending either path, since old doors vary a great deal.
Related services
- Deadbolt InstallationThe old deadbolt has grown lazy.
- Vintage Mortise Lock ServiceThe old skeleton key still fits the keyhole, but it now needs a jiggle, a lean on the door and a little luck before the bolt moves.
- Smart Lock InstallationArthritis has made the small house key hard to grip and turn, especially with gloves on in January.