Car keys · Westmount
Ignition Lock Repair in Westmount
Turning the key used to take one smooth motion.
In plain words
Winters here add road grit, salt and moisture to the list of things an ignition barrel deals with, on top of ordinary wear from years of daily use. A barrel that has gone stiff or gritty through a cold, slushy season is cleaned, serviced and lubricated rather than simply forced, and the fix holds up through the next stretch of the same weather.
How the visit goesThe car arrived with one worn-looking key and a story about a lost spare. It turns the ignition, eventually, after some patience and a particular angle nobody in the household can quite describe or repeat on the first try.
Ignition Lock Repair
How the visit goes
Looking for signs of an earlier attempt
Scratches around the slot, a loose-feeling housing, or a barrel that spins without any of the usual resistance can mean somebody already tried the lock before the locksmith arrived. Noting this before starting matters for two reasons: it changes the repair, since a lock that has been forced usually needs full replacement rather than a simple service, and it gives the owner an honest account of what was already there rather than what happened during this particular visit.
Repinning the cylinder to the current key
When the barrel itself needs to come out, it is removed from the housing and its wafers are reset to match the key already in use, following that vehicle's own service procedure rather than a generic pin-and-follower method. Reassembled and tested through every position, the repaired cylinder answers to the same key that opened the door on the way to the vehicle, so nothing else in the owner's pocket needs to change.
A little care that keeps the barrel turning smoothly
A cylinder that has just been serviced benefits from the same light touch that kept it healthy in the first place: whatever lubricant the vehicle's own service information calls for worked into the keyway every so often, since some ignitions specify grease rather than a dry product. Wipe debris off the key itself before each use, and retire a key that has started to look rounded or thin, well before it becomes the reason for another visit.
Ignition Lock Repair
In the van
Broken key extractors
Cylinder decoder
Pick and tension tools
Trim clips and fasteners
Key code reader
Ignition Lock Repair
What affects the quote
Access through the steering column
Reaching some ignition cylinders means removing trim, shrouding or fasteners around the column first, and putting all of it back cleanly afterward. A column that is straightforward to open takes less time than one that is not.
Keying other locks to match
Bringing the doors and trunk onto a newly pinned ignition key, so one key runs the whole vehicle again, is separate work from the ignition repair itself, even when it happens during the same visit.
Number of new keys cut
One replacement key is the simplest case. A household or a business vehicle used by several people may want a few keys cut and tested at once, and each one is counted into the visit.
What to have ready
- Do you have a spare or second key available?
- Is the key stuck and unable to be removed?
- Has this ignition been serviced or replaced before?
Ignition Lock Repair: questions
QuestionsMy key turns but the engine doesn't crank. Is that an ignition lock problem?
It can be, but it can also point past the lock entirely, toward the electronic immobilizer, the transponder chip in the key, or wiring behind the switch. The locksmith checks whether the barrel itself moves cleanly through every position first. If it does, and the vehicle still stays silent, the electronic side is one possibility among several, alongside the battery, starter and park/neutral circuit, so the cause is diagnosed rather than assumed.
Will the same key still open my doors and trunk after this repair?
If the doors and trunk already shared a key with the ignition, that arrangement is kept in mind throughout the repair and preserved wherever the vehicle's hardware allows it. Where a new cylinder or new pinning is involved, the other locks are tested against the new key before the visit ends, so nothing is left running on two different keys by accident.
What information should I have ready when I call?
The vehicle's year, make and model, and exactly what the key does: whether it inserts, turns, engages anything, or is stuck. Mention whether a spare key exists, whether anything has already been tried on the lock, and whether the vehicle's warning lights or dash behave normally otherwise. Having the vehicle permit or registration nearby helps the ownership check move along smoothly.
Related services
- Car Key ReplacementThe key snapped at the head while you were turning it in a stiff, frosty door lock.
- Spare Car Key DuplicationA lockout last month ended with a locksmith opening the door and going home, and the same single key has been carried ever since with nothing behind it.
- Key Fob ProgrammingA new driver has joined the household, and the one existing fob is the only key anyone has ever had cut for this vehicle.